Italy PIZZATO safety model switch introduction

Italy PIZZATO safety switch

    PIZZATO Italy is one of the most important manufacturers of position switches, safety switches, foot switches, micro switches and safety modules in Europe. The company produces more than 6,000 standard products and a variety of non-standard products to meet the needs of users. The company has nearly 100 people in the modern factory building of about 10,000 square meters to produce high quality PIZZATO products, and its products are certified by IMQ, UL, CSA, etc., and can be trusted. The main products are as follows:
    Heavy-duty switch series: FD type is metal casing, equipped with conduit introduction device, IP66 protection, service life up to 20 million times, model is FD502-1GM2K50; FP type is made of polyester glass reinforced material, self-extinguishing, anti-extinguishing Good vibration, double insulation, model FP605-1GM2K70; FL type is metal casing, epoxy powder coated, three-duct introduction device, IP66 protection, model such as FL701-2GM2K52; FC type is single-duct introduction device, operating temperature is -25 ° C - 80 ° C, model such as FC302-1M1;
    Conventional load switch series: FR type is made of polyester glass reinforced material, self-extinguishing, good vibration resistance, double insulation, IP65 protection, single conduit introduction device, model such as FR554-1GM2K70; FM series metal casing, epoxy Powder, IP65 protection, model such as FM602-2GM2K40; FX type is double conduit introduction device, the rest is the same as FR type, model is FX554-1GM2K71; FZ type is double conduit introduction device, the rest is the same as FM type, model is FZ554-1GM2K51 The FK type casing is similar to the FR type, such as FK354-1M1;
    Preset switch series: FA type metal casing, with epoxy powder, 2m 5*0.75 square mm SEV and IMQ standard cable, IP67 protection, model such as FA4101-2DN1G; FB type is similar to FA type, model is FB4602-2DN1G FF series adopts reinforced polyester glass casing, good vibration resistance, double insulation, 2m 4*0.75 square mm SEV and IMQ standard cable, model FF4808-2DG1G;
    FR type safety switch: FR17A3 type is used for overspeed device, switch actuator is automatically pressurized at the balance point, according to different contacts, similar models are FR5A3, FR11A3;
    FP type safety switch: middle and end foot switch with high-strength anti-vibration housing, ψ40mm rubber wheel, single-channel activation, model FP945-S3;
    M series micro switch: equipped with reinforced glass fiber and thermoplastic resin type door switch, 1NO-1NC conversion contact, IP20 protection without terminal sleeve or IP40 protection with terminal sleeve, similar products are MS45, MS53 and MS58;
    FT series safety switch: suitable for high induction capacity and low driving force, IP66 protective casing, speed 0.5m / s, model such as FT1101E230-M2;
    PX and PA series foot switch: equipped with non-slip rubber foot pad lifting plate, protection class IP53 and IP65, in line with CE certification, models such as PX10110-AM2, PA20621-BM2; similar as PX10110;
    E1 contact block: Suitable for FD, FP, FL, FR, FM, FX and FZ series switches, replacing the traditional mechanical contact block, increasing the application range of the switch;
    For non-inertial mechanical with independent actuator type switch: Heavy duty safety switch with control grid, sliding door and protective 拴 to protect the dangerous parts of the machine, such as FD693-F1GM2K50, FL993-F2GM2K52, FP3393-F7GM2K70; with self-locking The type switch only allows specific operations to be performed to prevent some operations that may cause damage to the switch. When the switch is in the closed state, the actuator can be held at 1000N, IP66 protection, model number: FD1899-F1GM2K50, FP3099-F2GM2K70;
    For inertial machine with independent actuator type switch: suitable for severe working conditions such as high temperature and high pressure, after the power is cut off, the machine will prevent damage to the machine due to the continuous operation of the pulley and the circular saw under inertia. Models such as FS0696D024-F1GM2K40 , FD6R2-L10F1GM2K50;
    Hinged safety switch: It is used to protect the dangerous parts of the machine. It can send an emergency stop protection signal very sensitively when the calibration angle is shifted or rotated. The model is FD1895-GM2K50. The chute hole type is more convenient to install without hinge mutual inductance. Models such as FR18C1-GM2K70, FM9C2-GM2K40, FX22C3-GM2K50, FZ34C4-GM2K72;
    Drawstring switch: with reset type, used for machinery and conveyor belt, can ensure the equipment to stop in case of dangerous situations, so as not to damage the machine, provide automatic control function, model such as FD678-GM2K50; without reset type support general stop function, model Such as FD679-GM2